Aluminum Awnings in North Carolina — Built for Coastal Wind & Piedmont Heat

1800Awnings manufactures custom aluminum awnings, architectural canopies, pergolas, and Bahama shutters for North Carolina homes and businesses — from the barrier islands to the Blue Ridge escarpment. Every unit is cut, welded, powder-coated, and crated at our own Tampa, Florida factory and freighted direct to your North Carolina address, built to the exact inch. We have been making shade systems for the Southeast since 1987.

Custom aluminum awning manufactured by 1800Awnings and shipped to North Carolina

North Carolina Awnings at a Glance

What we ship to North Carolina
Retractable awnings, aluminum window & door awnings, architectural canopies, pergolas, Bahama shutters, motorized solar and hurricane screens
Where it is made
Our own factory at 4608 N. Hale Ave, Tampa, FL — roughly 600 miles from Charlotte and about 700 from Raleigh
Shipping
Free freight shipping to all 48 contiguous states, including every ZIP code in North Carolina
Sizing
Built to the exact inch — no standard-size compromises
Install options
DIY knock-down kits (pre-cut, pre-drilled, stainless hardware) or fully assembled crated units for contractor install
North Carolina metros served
Charlotte, Raleigh, Durham, Greensboro, Winston-Salem, Fayetteville, Cary, Wilmington, Asheville, Concord, High Point, Greenville, Jacksonville, Hickory, New Bern, Boone, the Outer Banks
Phone
1-800-AWNINGS (1-800-296-4647)
Commercial aluminum awnings on a self-storage facility, the same construction shipped to North Carolina commercial projects

Engineered for North Carolina's Climate

Few states put an awning through three environments this different. Along the Outer Banks and the Cape Fear coast, the North Carolina building code places large stretches of Dare, Hyde, Carteret, New Hanover, and Brunswick counties in high-wind and wind-borne debris territory, where a hurricane or a stalled nor'easter drives salt spray miles inland. The classic failure there is not the fabric — it is the hardware. Zinc-plated screws bloom rust inside two seasons, steel tube frames weep orange down the siding, and a mill-finish aluminum edge that was never coated chalks white and pits. Inland, the Piedmont problem is heat: Charlotte, the Triad, and the Triangle stack 90-degree days with high dewpoints from June into September, and west-facing glass turns a living room into a solar collector while wood pergolas soak, swell, and rot. West of Marion the story flips again — Boone, Banner Elk, Blowing Rock, and the ridgelines above Asheville pick up real snow and freeze rain, and fabric awnings sag, pool, and tear under the load.

One construction answers all three. The frames are all aluminum, so there is no ferrous metal to rust in salt air. Every fastener is stainless steel. Architectural powder coat is applied to 100% of the surface — top, bottom, ends, and every cut edge — so there is no bare metal for chloride to attack, and no seam for a freeze-thaw cycle to work open. Because we control the extrusion, gauge, projection, and anchor spacing on your unit, we spec to the exposure you tell us you have — an oceanfront elevation at Nags Head is not built like a shaded Durham porch — and we supply shop drawings you can hand to your engineer or your county permit office.

Custom-sized aluminum awning built to exact measurements for a North Carolina home

You Are Buying from the Factory, Not a Middleman

Search for awnings in North Carolina and most of what comes back is a dealer network or a drop-shipper moving imported kits in fixed sizes. We are the plant. That is why we can build any dimension to the exact inch, hit a specific RAL number or an aluminum woodgrain finish, and detail the mounting for the wall you actually have — brick veneer over frame in Charlotte, fiber cement in a new Wake County subdivision, cedar shake on a Currituck cottage, or an EIFS storefront in a Greensboro retail strip.

It also strips out the dealer margin that normally sits between a North Carolina buyer and the person who welds the frame. And when you call, you get a technician, not a lead form. Send photos of the wall, your rough opening, and your desired projection; we will confirm the layout, tell you exactly where the brackets land, and stay on the phone or a video call while you set the first one.

What We Build for North Carolina Homes & Businesses

Retractable Awnings

Motorized & manual patio shade, built to size.

Aluminum Awnings

Window, door & storefront awnings that never rust.

Pergolas

Modern & coastal aluminum pergola systems.

Shutters

Bahama, colonial & architectural aluminum shutters.
Commercial open-tube aluminum awnings in a custom color on a retail storefront

Residential and Commercial Work Across the State

Residential orders cluster by region. In Charlotte and the Raleigh-Durham Triangle, it is mostly motorized retractables over rear decks and window awnings on the west elevation to cut afternoon heat gain before it reaches the glass. On the coast around Wilmington, Wrightsville, Southport, and the Outer Banks rental corridor, it is Bahama shutters, deep door hoods, and aluminum pergolas that can be left up year-round. Around Asheville and the High Country, homeowners choose fixed aluminum over fabric specifically because it sheds snow and ice instead of holding it.

Commercially we ship storefront canopies and entry awnings to Piedmont retail centers, restaurant patios in downtown Durham and South End, self-storage and flex-industrial developments along the I-85 and I-40 corridors, medical office entries, and apartment communities that need twenty matching units delivered on one truck. Commercial buyers usually take fully assembled crated units so a local crew can hang the run in a day; homeowners more often take the knock-down kit, which arrives pre-cut, pre-drilled, and bagged with stainless hardware and instructions. Both are the same commercial-grade product.

North Carolina Cities We Ship To

  • Charlotte
  • Raleigh
  • Greensboro
  • Durham
  • Winston-Salem
  • Fayetteville
  • Cary
  • Wilmington
  • High Point
  • Concord
  • Asheville
  • Greenville
  • Jacksonville
  • Chapel Hill
  • Huntersville
  • Apex
  • Burlington
  • Rocky Mount
  • Kannapolis
  • Mooresville
  • Wake Forest
  • Hickory
  • Gastonia
  • Holly Springs
  • New Bern
  • Wrightsville Beach
  • Southport
  • Nags Head
  • Boone
  • Pinehurst

North Carolina Awning FAQs

Do you ship awnings to North Carolina?

Yes — to every ZIP code in the state. We freight factory-direct from Tampa to Charlotte, the Triad, the Triangle, Fayetteville, Wilmington and the Cape Fear coast, the Outer Banks, and the mountain counties. Shipping is free to all 48 contiguous states, and your order arrives either as a DIY knock-down kit or as a fully assembled crated unit.

How much do aluminum awnings cost in North Carolina?

Every unit is made to order, so the price follows size, style, and finish — not your delivery address. Freight to North Carolina is free, which means a Charlotte or Kill Devil Hills customer pays exactly what a Florida customer pays for the same awning. Retractable awnings start around $1,924. Send measurements and we will quote the exact configuration.

Will these hold up to hurricane wind and salt air on the North Carolina coast?

Coastal exposure is what this construction is built for. There is no steel in the frame to rust, the fasteners are stainless, and the powder coat covers 100% of every surface — including the underside and the cut ends, which is where cheaper awnings begin to corrode. We do not publish a blanket wind rating for another state's code; instead we build to the exposure you describe, size the gauge and anchor pattern accordingly, and send drawings your engineer or the county can review for a wind-borne debris zone submittal.

Do you have installers in North Carolina?

No — our own crews work the Tampa Bay area only, and we will not claim otherwise. North Carolina orders go out as a DIY kit that a reasonably handy homeowner can mount, or as a fully assembled crated unit that any local contractor, handyman, or commercial installer can hang in a few hours. Shop drawings plus phone and video support during the install are included at no charge.

Can you build to an HOA color or a historic-district requirement?

Yes. As the manufacturer we powder-coat to any RAL color and offer aluminum woodgrain finishes that read as stained wood but never need refinishing. If a Ballantyne or Brier Creek HOA specifies a color, or a local historic commission in Wilmington, New Bern, Edenton, or Beaufort specifies a profile, projection, or scalloped valance, send us the written requirement — we build to it and supply drawings for the submittal.

How long does a North Carolina order take?

Production usually runs a few weeks depending on the product and where the queue stands, then add freight transit from Tampa — generally two to four days to North Carolina, with the coast and the Piedmont typically ahead of the far western counties. Call 1-800-296-4647 for the current lead time on your specific product before you order.

Get a Custom Quote for Your North Carolina Project

Send us your sizes, finish, and delivery address. We build it in Tampa and ship it free anywhere in North Carolina — one window awning or a hundred storefront canopies.

Call 1-800-296-4647 • Request a Quote

Serving other states? See all 1800Awnings service areas.